Over 30 years' experience · All trades in-house · Fully insured Call 07811 466054
Call 07811 466054 Free Quote
Tilers in Worksop, Mansfield & North Derbyshire — work by Barbers Bathrooms & Kitchens
Tiling

Tilers in Worksop, Mansfield & North Derbyshire

Barbers Bathrooms & Kitchens carries out wall and floor tiling across North Derbyshire, Nottinghamshire and South Yorkshire — bathrooms, wet rooms, kitchens, hallways and utility rooms. Preparation, tanking, tiling and sealing are all handled by the same team.

Get Your Free Quote Call 07811 466054
Preparation
Roughly 70% of the job — and where failures start
Tanking
Included as standard in every wet area we tile
Standalone work
Yes — floors, splashbacks and single rooms welcome
Where we work
Worksop, Clowne, Bolsover, Mansfield & 30 miles of Creswell

What Good Tiling Actually Depends On

Tiling is preparing a surface, setting tiles into adhesive to a true line and level, then grouting and sealing the finished surface.

Roughly 70% of the work is preparation. Almost every tiling failure traces back to it rather than to the tiling itself.

Getting the substrate right is unglamorous, and it is the entire job.

  • A wall out of plumb will show in every grout line
  • A timber floor that deflects will crack a rigidly bedded tile
  • A shower area that was never tanked will let water past the grout
  • A substrate that was not primed dries the adhesive out before it cures
  • Setting out decides where the cuts land — and whether the room reads as deliberate
Get a fixed price for this
Close-coupled toilet and vanity basin against dark blue metro tiling

Why Tiling Is Where Corners Get Cut

Tiling is the last visible trade in a bathroom or kitchen, so it absorbs every delay that came before it.

By the time the tiler starts, the job is late and the pressure is to get it done rather than get it right.

That is when the tanking gets skipped, the floor gets tiled without a decoupling layer, the large-format porcelain goes onto a wall nobody straightened, and the cuts land in the worst possible places.

  • The plumbing, electrics and plastering behind the tiling are ours too
  • Nothing reaches the tiling stage in a state that forces a compromise
  • Tanking, backer board and levelling are quoted up front, not discovered later
  • Cuts planned so they land where they will not be seen
Traditional fitted vanity units and a shower screen in a family bathroom

Planning wall & floor tiling? A survey and a fixed written quote cost you nothing.

Book a Free Survey 07811 466054
How we work

How We Work

01

Substrate preparation

Walls are checked for plumb and flatness, floors for movement. Where needed we overboard, level, or install backer board — particularly on timber floors, which move and will crack a rigidly bedded tile.

02

Tanking and priming

Shower areas and wet rooms are tanked with a liquid membrane taken up the walls and into the corners. Absorbent substrates are primed so the adhesive cures rather than dries out.

03

Setting out

We plan the tile layout before a single one is fixed — where the full tiles land, where the cuts fall, how the pattern meets a corner and a window reveal. This is the difference between a good tiled room and an average one.

04

Tiling, grouting and sealing

Tiles are fixed to line and level, then grouted and the movement and change-of-plane joints sealed with silicone rather than grouted rigid. Natural stone is sealed before and after grouting.

A standard bathroom takes 2 to 4 days to tile, depending on tile size and how much cutting there is. A kitchen splashback is often a single day. Large-format porcelain and mosaic both take longer than they look.

Walk-in shower with a black towel radiator and marble-effect wall tiles
Walls checked for plumb, floors for movement, and backer board fitted where timber floors would crack a tile.
Shower wall tiled with levelling clips still in place during installation
Wet areas tanked with a liquid membrane taken up the walls and into every corner before a tile goes on.
Walk-in shower screen and recessed niche part-way through tiling
Set out first, then fixed to line and level — cuts land where they will not be seen.
Scope

What We Tile

Quotes vary between companies mostly because of what they leave out. Here is exactly what is in ours, what counts as extra, and what you would normally supply.

What is included as standard?

  • Full bathroom and shower room wall and floor tiling
  • Wet room tiling over a tanked, falls-formed floor
  • Kitchen splashbacks and full-height kitchen walls
  • Hallway, utility and conservatory floors
  • Large-format porcelain, including 1200mm+ formats
  • Natural stone, sealed correctly before and after grouting
  • Mosaic, metro, herringbone and patterned layouts
  • Backer board, overboarding and floor levelling
  • Tanking of wet areas
  • Underfloor heating installed beneath tiled floors

What is quoted separately?

  • Lifting and disposing of existing tiled floors where extensive
  • Structural floor strengthening where deflection is beyond normal preparation
  • Supply of the tiles themselves, unless you ask us to source them

What do you usually supply?

  • Tiles, trims and any specific grout colour
  • — adhesive, tanking, backer board and sealant are all included
Get this quoted for your home See finished work

How Much Does Tiling Cost?

Tiling is priced per square metre, but the rate moves a long way with the tile and the substrate.

What moves the price

  • The tile itself. Large-format porcelain, natural stone, mosaic and herringbone all take substantially longer to lay than a standard ceramic.
  • Condition of the substrate. A wall that needs straightening or a floor that needs backer board adds preparation before any tiling starts.
  • Whether the area needs tanking. Showers, wet rooms and the wall behind a bath need a waterproof membrane. It is not optional and it is not free.
  • Cutting and pattern. Herringbone, patterned layouts and lining a pattern through at reveals all take more setting-out time.
  • Size of the area. Small rooms cost more per square metre than large ones — the setup is the same either way.

We quote after seeing the room and the tile you have chosen, because quoting per square metre without knowing either is how tiling quotes end up revised.

We publish price ranges only once they are current and accurate for this area, rather than quoting a national average that would not survive a home visit. Call or WhatsApp us on 07811 466054 and we will give you a realistic ballpark for your room over the phone, then a fixed written figure after we have seen it.

Quadrant shower enclosure, toilet and basin in a grey-tiled bathroom
Free · No obligation

How do I get a fixed quote for wall & floor tiling?

We visit, measure up, check what is behind the walls, and put a written price in your hands. No charge, no obligation, no follow-up sales visit.

Rather talk? Call 07811 466054 or message us on WhatsApp. Mon–Fri 7:30am–8:30pm.

Why Barbers

Why Choose Barbers for Tiling

Vanity basin below a narrow window in a grey-tiled cloakroom

Preparation is not an optional extra

Tanking, backer board, priming and levelling are quoted and carried out as standard where the room needs them. They are the difference between tiling that lasts twenty years and tiling that fails in three.

Low-profile shower tray and enclosure beside a white ladder radiator

Setting out done properly

Cuts are planned so they land where they will not be seen, patterns line through at corners and reveals, and the room reads as deliberate rather than as whatever the first tile decided.

Fitted vanity unit, mirror and shower screen in a marble-effect bathroom

One team through the whole room

The plumbing, electrics and plastering behind the tiling are ours. The tiler is not inheriting somebody else's problems and pricing around them.

Marble-effect tiling run around a panelled door in a shower room

Standalone tiling welcome

We take on tiling as a job in its own right, not only as part of a bathroom or kitchen. Floors, splashbacks and single rooms are all normal work.

Barbers Bathrooms & Kitchens is run by Dan Barber, Master Joiner & Director. About us and how we work · Our workmanship guarantee and complaints route · Rated 5.0 on Google from 6 reviews (October 2026)

Where we work

Tilers Across Worksop, Mansfield & Chesterfield

Most of our tiling sits inside bathroom and kitchen projects across Worksop, Clowne, Bolsover, Mansfield and Chesterfield.

Standalone tiling is common too — a hallway floor in a Victorian terrace, a full-height wall in a Barlborough new build, or a wet room floor in Shirebrook needing falls formed to a central drain.

Older properties across the Bolsover and Bassetlaw villages frequently need floor preparation first, because suspended timber floors move and will crack a tile bedded straight onto boards.

See the full list of areas we cover — no travel charge anywhere within 30 miles of Creswell.

Black marble-effect tiled shower room with a gilt-framed mirror
Our work

Recent Tiling

View the full gallery

Good to know

Frequently Asked Questions About Wall & Floor Tiling

Can you tile straight onto a timber floor?
No, tiles should not be bedded directly onto floorboards, because timber floors move and the tile or grout will crack. The correct method is to overboard with a tile backer board or ply, fixed at close centres, or to use a decoupling matting system. We assess the deflection in the floor before quoting and include the right preparation in the price.
Do shower walls need tanking before tiling?
Yes, any area subject to direct or frequent water — shower enclosures, wet rooms, and the wall behind a bath with a shower over — should be tanked with a waterproof membrane before tiling. Tile and grout are not waterproof; they are water-resistant, and water will find the substrate behind them eventually. Tanking is included as standard in our bathroom work.
Can you tile over existing tiles?
It is sometimes possible to tile over existing tiles if they are sound, well bonded and flat, and the substrate can take the extra weight. In practice we usually recommend removing them, because you inherit any weakness in the original fixing and the finished surface stands proud at doorways and reveals. We will tell you which applies in your room.
How long before I can use a newly tiled shower?
Allow 24 hours after grouting before using a newly tiled shower, and 24 hours after silicone is applied before it gets wet. Floors should not be walked on for at least 24 hours after fixing. We will tell you the exact timings for the products used on your job at handover.
Can you tile onto plywood or plasterboard?
Plasterboard, yes, on walls in dry areas, primed first; in showers and wet rooms we tile onto tile backer board or a tanked surface instead, because plasterboard fails when it gets wet. Plywood on floors is a poor base — thin ply flexes and cracks the tiles — so we overlay timber floors with cement backer board or a decoupling membrane and tile onto that.
Do you fit underfloor heating under tiles?
Yes, we install electric underfloor heating mats and loose wire systems beneath tiled floors, along with the insulation board that makes them worth having. The connection to the fused spur and thermostat is carried out as part of the electrical work on the job. Underfloor heating is one of the highest-value additions to a bathroom and is far cheaper to fit while the floor is already up.
Which grout should I choose?
For most walls and floors a good flexible cement-based grout is right, and it comes in a wide range of colours. Epoxy grout is harder wearing and resists staining, which suits a busy kitchen floor or a shower tray area, but it is slower to apply and has to be cleaned off the tile face quickly. Pale grout on a floor will darken with use; a mid-grey hides it. We will talk you through the options against the tile you have picked.
Do large-format tiles need anything different?
Yes. A big porcelain tile shows every dip in the wall or floor, so the surface has to be flatter than it would for a small tile, and we check it with a long straight edge before starting. The tile is back-buttered as well as the bed being combed, so there are no hollow spots, and a levelling clip system keeps neighbouring edges flush. The weight matters too: some plaster finishes cannot carry a heavy tile, and in that case the wall is boarded first.

Still deciding? A survey costs nothing and you will know exactly what the job involves.

Request Your Free Quote 07811 466054
Further reading

What Should You Read Before You Start?

How Much Does a Tiler Cost? Day Rates and Prices per m² for 2026

Published 2026 UK cost guides put a tiler's labour at roughly £20 to £40 per m² for standard tiles, and a day rate of £150 to £250, with some sources going to £300. Supplied and fitted, wall tiling runs from about £60 per m² for ceramic to £200 or more for mosaic. Tile size, pattern and the preparation underneath move the price far more than the area does.

Read the guide

Best Bathroom Flooring UK: Tile, LVT, Vinyl & Stone Compared

The best floor coverings for bathrooms are porcelain tile, luxury vinyl tile (LVT) and welded sheet vinyl, because all three cope with standing water. Porcelain tile is the best bathroom flooring for most UK homes: it barely absorbs water, lasts for decades and works with underfloor heating. Luxury vinyl tile (LVT) is the best alternative where warmth, quiet and budget matter more, and welded sheet vinyl is the budget choice for a wet room. Natural stone looks best but needs sealing. Most laminate and all solid wood are poor choices. Choose a tile with a low slip potential (a pendulum test value of 36 or more, by HSE guidance), and remember that the subfloor preparation decides whether any bathroom floor lasts.

Read the guide

Walk-In Shower vs Wet Room: Which Is Right for Your Bathroom?

A wet room is a fully tanked room where the whole floor is waterproofed and laid to a fall, with no shower tray. A walk-in shower uses a low-profile or flush tray with a fixed screen. Wet rooms give true level access and suit small rooms and accessibility needs; walk-in showers are quicker, cheaper and suit most standard family bathrooms.

Read the guide

Small Bathroom Ideas That Actually Work

The changes that gain most in a small bathroom are structural rather than decorative: removing the wall to a separate WC, replacing a bath with a walk-in shower or wet room, wall-hung sanitaryware, and a door that opens outwards. Colour and mirrors help, but they do not add space.

Read the guide
Related

You Might Also Need

Bathroom Installation

Barbers Bathrooms & Kitchens installs complete bathrooms for homeowners across North Derbyshire, Nottinghamshire and South Yorkshire.

Learn more

Plastering

Barbers Bathrooms & Kitchens carries out plastering, skimming, boarding and rendering repairs across North Derbyshire, Nottinghamshire and South Yorkshire — as part of a full renovation or as a standalone job.

Learn more

Kitchen Installation

Barbers Bathrooms & Kitchens designs, supplies and installs complete kitchens across North Derbyshire, Nottinghamshire and South Yorkshire, and fits supply-only kitchens bought from Howdens, Wren, B&Q or any other supplier.

Learn more
Free, no-obligation quote

Planning wall & floor tiling? Get a fixed quote.

We visit, measure up, check what's behind the walls and give you a written price with the exclusions stated plainly. No obligation, no charge, no sales visit.

Much of our work comes from repeat customers and recommendations, reflecting the standard we work to.

Request a Free Quote See Our Work
Contact us

Barbers Bathrooms & Kitchens

Creswell, Derbyshire Service area business — we work in your home

We cover a 30-mile radius of Creswell, including Worksop, Clowne, Bolsover, Mansfield, Chesterfield, Retford, Sheffield and Nottingham. There is no travel charge anywhere within that area.

Phone
07811 466054
Hours
Monday to Friday: 7:30am – 8:30pm
Call now WhatsApp Free quote